Надпись support apple com mac startup

Компьютер Mac загружается до логотипа Apple или индикатора выполнения

Логотип Apple отображается на экране компьютера Mac после обнаружения локального загрузочного диска, затем ход запуска или установки macOS отображается с помощью индикатора выполнения.

Компьютер Mac отображает логотип Apple, когда находит загрузочный диск (обычно это встроенный диск компьютера Mac). По мере продолжения запуска вы увидите индикатор выполнения с логотипом Apple или без него. Этот экран может несколько раз сменяться пустым экраном.

Во время установки macOS логотип Apple или индикатор выполнения может отображаться намного дольше, чем обычно. В процессе установки индикатор выполнения может заполняться очень медленно и оставаться на одной отметке длительное время. Поэтому компания Apple рекомендует начинать установку macOS вечером, чтобы она завершилась за ночь.

Компьютер Mac завис на этом экране

Если вы полагаете, что ждали достаточно долго, и компьютер Mac завис на этом экране, выполните следующие действия.

  1. Нажмите и удерживайте кнопку питания в течение 10 секунд, пока компьютер Mac не выключится. После этого снова включите компьютер Mac.
  2. Если проблема сохраняется, нажмите и удерживайте кнопку питания, пока компьютер Mac не выключится. Затем отключите от компьютера Mac все аксессуары, включая принтеры, диски, USB-концентраторы, а также другие необязательные устройства. Проблема может быть связана с одним или несколькими из этих устройств или их кабелями. После этого снова включите компьютер Mac.
  3. Если проблема сохраняется, еще раз нажмите и удерживайте кнопку питания, пока компьютер Mac не выключится. Затем восстановите загрузочный диск с помощью приложения «Дисковая утилита».
    • Если приложение «Дисковая утилита» не обнаружило ошибок, переустановите macOS.
    • Если приложение «Дисковая утилита» обнаружило ошибки и исправило их, перезапустите компьютер Mac. Если после перезапуска проблема возникает снова, переустановите macOS.
  4. Если требуется дополнительная помощь, обратитесь в службу поддержки Apple.

Источник

Mac startup key combinations

Learn about the Mac features and tools that you can access by holding down one or more keys during startup.

On a Mac with Apple silicon

Turn on your Mac with Apple silicon and continue to press and hold the power button until you see the startup options window. From there you can start up from a different disk, start up in safe mode, use macOS Recovery, and more. Learn more about these options, including macOS Recovery.

On an Intel-based Mac

To use any of these key combinations, press and hold the keys immediately after pressing the power button to turn on your Mac, or after your Mac begins to restart. Keep holding until the described behavior occurs.

  • Command (⌘)-R: Start up from the built-in macOS Recovery system. Or use Option-Command-R or Shift-Option-Command-R to start up from macOS Recovery over the internet. macOS Recovery installs different versions of macOS, depending on the key combination you use. If your Mac is using a firmware password, you’re prompted to enter the password.
  • Option (⌥) or Alt: Start up to Startup Manager, which allows you to choose other available startup disks or volumes. If your Mac is using a firmware password, you’re prompted to enter the password.
  • Option-Command-P-R:Reset NVRAM or PRAM. If your Mac is using a firmware password, it ignores this key combination or starts up from macOS Recovery.
  • Shift (⇧): Start up in safe mode. Disabled when using a firmware password.
  • D: Start up to the Apple Diagnostics utility. Or use Option-D to start up to this utility over the internet. Disabled when using a firmware password.
  • N: Start up from a NetBoot server, if your Mac supports network startup volumes. To use the default boot image on the server, press and hold Option-N instead. Disabled when using a firmware password.
  • Command-S: Start up in single-user mode. Disabled in macOS Mojave or later, or when using a firmware password.
  • T: Start up in target disk mode. Disabled when using a firmware password.
  • Command-V: Start up in verbose mode. Disabled when using a firmware password.
  • Eject (⏏) or F12 or mouse button or trackpad button: Eject removable media, such as an optical disc. Disabled when using a firmware password.
Читайте также:  Как выглядит айфон 12 мини сзади

If a key combination doesn’t work at startup, one of these solutions might help:

  • Press and hold all keys in the combination together, not one at a time.
  • Shut down your Mac. Then press the power button to turn on your Mac. Then press and hold the keys as your Mac starts up. You might need to wait a few seconds before pressing the keys, to give your Mac more time to recognize the keyboard as it starts up. Some keyboards have a light that flashes briefly at startup, indicating that the keyboard is recognized and ready for use.
  • If you’re using a wireless keyboard, plug it into your Mac, if possible. Or use your built-in keyboard or a wired keyboard. If you’re using a keyboard made for a PC, such as a keyboard with a Windows logo, try a keyboard made for Mac.
  • If you’re using Boot Camp to start up from Microsoft Windows, set Startup Disk preferences to start up from macOS instead. Then shut down or restart and try again.

Источник

Mac startup key combinations

Learn about the Mac features and tools that you can access by holding down one or more keys during startup.

On a Mac with Apple silicon

Turn on your Mac with Apple silicon and continue to press and hold the power button until you see the startup options window. From there you can start up from a different disk, start up in safe mode, use macOS Recovery, and more. Learn more about these options, including macOS Recovery.

On an Intel-based Mac

To use any of these key combinations, press and hold the keys immediately after pressing the power button to turn on your Mac, or after your Mac begins to restart. Keep holding until the described behavior occurs.

  • Command (⌘)-R: Start up from the built-in macOS Recovery system. Or use Option-Command-R or Shift-Option-Command-R to start up from macOS Recovery over the internet. macOS Recovery installs different versions of macOS, depending on the key combination you use. If your Mac is using a firmware password, you’re prompted to enter the password.
  • Option (⌥) or Alt: Start up to Startup Manager, which allows you to choose other available startup disks or volumes. If your Mac is using a firmware password, you’re prompted to enter the password.
  • Option-Command-P-R:Reset NVRAM or PRAM. If your Mac is using a firmware password, it ignores this key combination or starts up from macOS Recovery.
  • Shift (⇧): Start up in safe mode. Disabled when using a firmware password.
  • D: Start up to the Apple Diagnostics utility. Or use Option-D to start up to this utility over the internet. Disabled when using a firmware password.
  • N: Start up from a NetBoot server, if your Mac supports network startup volumes. To use the default boot image on the server, press and hold Option-N instead. Disabled when using a firmware password.
  • Command-S: Start up in single-user mode. Disabled in macOS Mojave or later, or when using a firmware password.
  • T: Start up in target disk mode. Disabled when using a firmware password.
  • Command-V: Start up in verbose mode. Disabled when using a firmware password.
  • Eject (⏏) or F12 or mouse button or trackpad button: Eject removable media, such as an optical disc. Disabled when using a firmware password.
Читайте также:  Apple dvd player для windows

If a key combination doesn’t work at startup, one of these solutions might help:

  • Press and hold all keys in the combination together, not one at a time.
  • Shut down your Mac. Then press the power button to turn on your Mac. Then press and hold the keys as your Mac starts up. You might need to wait a few seconds before pressing the keys, to give your Mac more time to recognize the keyboard as it starts up. Some keyboards have a light that flashes briefly at startup, indicating that the keyboard is recognized and ready for use.
  • If you’re using a wireless keyboard, plug it into your Mac, if possible. Or use your built-in keyboard or a wired keyboard. If you’re using a keyboard made for a PC, such as a keyboard with a Windows logo, try a keyboard made for Mac.
  • If you’re using Boot Camp to start up from Microsoft Windows, set Startup Disk preferences to start up from macOS instead. Then shut down or restart and try again.

Источник

Компьютер Mac не включается

Если компьютер Mac не включается после нажатия кнопки питания, выполните следующие действия.

Принудительное выключение компьютера Mac и последующее включение

Ваш компьютер Mac может быть включен, но кажется, что компьютер выключен, даже если он подключен к источнику переменного тока и исправному дисплею. Выполните следующие действия.

  1. Нажмите и удерживайте кнопку питания на компьютере Mac не менее 10 секунд, а затем отпустите ее. Если компьютер Mac включен, это действие приведет к его выключению.
  2. Если в состоянии компьютера Mac ничего не меняется, нажмите и отпустите кнопку питания.
  3. Если компьютер Mac включился, но загрузка останавливается на каком-то экране в процессе запуска, выполните действия, приведенные в статье Если компьютер Mac не запускается полностью.
Читайте также:  Для чего покупать apple tv

Регенерация прошивки (если применимо)

Если у вас компьютер Mac с чипом Apple или компьютер Mac с чипом безопасности Apple T2, в очень редких случаях может потребоваться регенерация или восстановление прошивки, хранящейся в памяти компьютера. Вот, что вам потребуется:

  • Другой компьютер Mac с macOS Catalina 10.15.6 или более поздней версии, а также последняя версия приложения Apple Configurator, которое можно бесплатно скачать в App Store.
  • Кабель USB-C/USB-C или USB-A/USB-C для соединения двух компьютеров. Кабель должен поддерживать передачу данных и зарядку. Кабели Thunderbolt 3 не поддерживаются.

Если у вас есть все необходимое, выполните следующие действия:

Если компьютер Mac по-прежнему не включается, вам требуется помощь по выполнению этих инструкций или у вас нет необходимых компонентов, обратитесь в службу поддержки Apple.

Источник

Change your Mac startup disk

You can make your Mac start up from a CD or DVD, a network volume, a different disk, or another operating system. To do so, you change your startup disk.

Important: If you have a Mac with an Apple T2 chip, added security features may need to be set in order to change the startup disk. See What is the Startup Security Utility?

Change your startup disk once

With your Mac or Mac with Apple silicon turned off:

On a Mac: Press and hold the Option key as you start up your Mac.

On a Mac with Apple silicon: Press and hold the power button until you see “Loading startup options”.

If you’re using a Mac mini, wait for the system indicator light to turn amber.

When you see the available startup disks, select one, then click the Up arrow (on Mac) or Continue button (on Mac with Apple silicon).

The next time you restart your computer, it starts up from the disk selected as your startup disk in System Preferences.

Change your startup disk for every startup

On your Mac, choose Apple menu

> System Preferences, then click Startup Disk .

If the lock at the bottom left is locked , click it to unlock the preference pane.

Click the icon of the disk you want to use, then click Restart.

WARNING: When selecting a network startup volume, make sure you select a network startup volume and not a network install image. Choosing a network install image reinstalls your system software and may erase the contents of your disk. A standard network volume icon appears as a globe with a folder. A network install icon appears as a globe with a downward-pointing green arrow.

Источник

Оцените статью